Did an across the wire migration recently and everything is working fine, except Apache with HTTPS. Apache works OK at port 80, but not 443. On the other hand, things like Portal (Https://.....:8009) work fine as well. I have gone into ConsoleOne to validate my certificates and they all check out valid and are current. I have run PKIDIAG with no errors. I have verified settings in the .conf files for Apache and ADMSrv as well and am now forcing Apache to latch onto just the main IP address of the server and not to all IP addresses (we have a secondary IP). HTTPSTK.NLM is loaded OK. I did have to uninstall and re-install Apache after the migration due to other Apache problems, but those problems went away (Apache would not work at all before). Any hints? Perhaps this is just a minor configuration issue? Note that I do have Groupwise WebAccess install as well (which works with HTTP but not HTTPS). Thanks.

Here is first part of my Apache httpd.conf file:

# NWConfVersion = 28
#
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
#
# NOTE! If you intend to place this on an NFS (or otherwise network)
# mounted filesystem then please read the LockFile documentation
# (available at <URL:http://httpd.apache.org/docs-2.0/mod/core.html#lockfile>);
# you will save yourself a lot of trouble.
#
# Do NOT add a slash at the end of the directory path.
#
ServerRoot "SYS:/APACHE2"

#
# Timeout: The number of seconds before receives and sends time out.
#
Timeout 300

#
# KeepAlive: Whether or not to allow persistent connections (more than
# one request per connection). Set to "Off" to deactivate.
#
KeepAlive On

#
# MaxKeepAliveRequests: The maximum number of requests to allow
# during a persistent connection. Set to 0 to allow an unlimited amount.
# We recommend you leave this number high, for maximum performance.
#
MaxKeepAliveRequests 100

#
# KeepAliveTimeout: Number of seconds to wait for the next request from the
# same client on the same connection.
#
KeepAliveTimeout 15

# NetWare MPM
# ThreadStackSize: Stack size allocated for each worker thread
# StartThreads: Number of worker threads launched at server startup
# MinSpareThreads: Minimum number of idle threads, to handle request spikes
# MaxSpareThreads: Maximum number of idle threads
# MaxThreads: Maximum number of worker threads alive at the same time
# MaxRequestsPerChild: Maximum number of requests a thread serves. It is
# recommended that the default value of 0 be set for this
# directive on NetWare. This will allow the thread to
# continue to service requests indefinitely.

ThreadStackSize 65536
StartThreads 25
MinSpareThreads 10
MaxSpareThreads 50
MaxThreads 1024
MaxRequestsPerChild 0
MaxMemFree 100

#
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, in addition to the default. See also the <VirtualHost>
# directive.
#
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses (0.0.0.0)
#
#Listen 12.34.56.78:80
Listen 172.16.1.10:80
SecureListen 172.16.1.10:443 "SSL CertificateDNS"

#
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. admin@your-domain.com
#
ServerAdmin dhess@djhnet.com

#
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
#
# If this is not set to valid DNS name for your host, server-generated
# redirections will not work. See also the UseCanonicalName directive.
#
# If your host doesn't have a registered DNS name, enter its IP address here.
# You will have to access it by its address anyway, and this will make
# redirections work in a sensible way.
#
ServerName 172.16.1.10