Upgraded from SLES 9 SP3 and OES1 SP2 to SLES 10 SP3 and OES2 SP2a. Upgrade went fine, didn't see any errors.

System came back up, cannot access either volume (POOL1/VOL1 and POOL2/ITFILES). Wait 2-3 minutes and NSS finally starts, I can now access POOL2/ITFILES but not POOL1/VOL1.

Both were available and working fine before the upgrade.

Run nssmu:
Devices: Shows both arrays
Partitions: Shows sda1, sda2, sda3.1 (all are correct, POOL2 is on this one). sdb1.1 is there, State: used, Pool: POOL1, Type: NSS. Total space, data area, and used space all match (like POOL2). I hit Enter, states Partition contains no volumes.
Pools: Only lists POOL2.
Volumes: Only lists ITFILES

fstab:
/dev/evms/lvm/system/sys_lx / reiserfs acl,user_xattr 1 1
/dev/evms/sda1 /boot reiserfs acl,user_xattr 1 2
/dev/evms/lvm/system/swap swap swap pri=42 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
proc /proc proc defaults 0 0
usbfs /proc/bus/usb usbfs noauto 0 0
sysfs /sys sysfs noauto 0 0
/dev/fd0 /media/floppy auto noauto,user,sync 0 0
VOL1 /media/nss/VOL1 nssvol noauto,rw,name=VOL1,norename 0 0
ITFILES /media/nss/ITFILES nssvol noauto,rw,name=ITFILES,norename 0 0

df -h:
Filesystem Size Used Avail Use% Mounted on
/dev/evms/lvm/system/sys_lx
25G 9.4G 16G 38% /
udev 2.0G 212K 2.0G 1% /dev
/dev/evms/sda1 306M 49M 258M 16% /boot
/dev/evms/POOL2 238G 149G 90G 63% /opt/novell/nss/mnt/.pools/POOL2
admin 4.0M 0 4.0M 0% /_admin
ITFILES 238G 148G 90G 63% /media/nss/ITFILES
Trinity:~ #


dmesg:
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
NSSLOG ==> [Error] comnVol.c[2989]
Mar 2, 2010 5:35:56 am NSS<COMN>-4.12a-660:
Volume VOL1 not found. Verify Media, Devices, Drivers and power
to subsystem. Try NSS /Activate=VOL1 and or type NSS /volumes and
verify spelling of the volume
Volume Change State failed. Error = 20801
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: device 253:5 too small for target
device-mapper: table: 253:8: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
---
nsscon only lists POOL2.

ls -l /dev/evms:
total 0
drwxr-xr-x 3 root root 220 Mar 2 05:42 .nodes
brw-r----- 1 root root 253, 7 Mar 2 00:30 POOL2
drwxr-xr-x 2 root root 60 Mar 2 05:42 dm
drwxr-xr-x 3 root root 60 Mar 2 00:30 lvm
brw-r----- 1 root root 253, 3 Mar 2 00:30 sda1

ls -l /opt/novell/nss/mnt/.pools:
total 0
drwxrwxrwx 2 root root 48 May 7 2007 POOL1
d--------- 1 root root 0 Mar 2 05:35 POOL2

I cannot get POOL1/VOL1 to mount no matter what I do... I've been at this for 12+ hours now, staff will be coming in to find no home directories today.

I figure I'm missing something simple, or at least I HOPE it's something simple.

If it matters, POOL2/ITFILES is on an internal array, and POOL1/VOL1 is on an external array.

Hopefully someone can point me in the correct direction.

Thank you in advance!